GM Service Manual Online
For 1990-2009 cars only

Tools Required

Snap-On A173A Bent Tip Awl or Equivalent

Removal Procedure

  1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  2. Caution: This vehicle is equipped with a Supplemental Inflatable Restraint (SIR) System. Failure to follow the correct procedure could cause the following conditions:

       • Air bag deployment
       • Personal injury
       • Unnecessary SIR system repairs
    In order to avoid the above conditions, observe the following guidelines:
       • Refer to SIR Component Views in order to determine if you are performing service on or near the SIR components or the SIR wiring.
       • If you are performing service on or near the SIR components or the SIR wiring, disable the SIR system. Refer to Disabling the SIR System.

  3. Disable the SIR system. Refer to Disabling the SIR System in SIR.
  4. Remove the steering wheel. Refer to Steering Wheel Replacement .

  5. Object Number: 777650  Size: SH
  6. Remove the tilt lever close out plate.
  7. Remove the retaining screw from the lower steering column trim covers.
  8. Tilt the trim cover down and slide rearward in order to disengage the locking tabs. Remove the lower steering column trim covers.
  9. Remove the retaining screws from the upper steering column trim cover.

  10. Object Number: 850886  Size: SH
  11. Lift the trim cover in order to gain access to the lock cylinder access hole (1).

  12. Object Number: 850894  Size: SH
  13. Insert the Snap-On A173A bent-tip awl (1) or equivalent, with a 2.5 mm (3/32 in) tip, and 20 mm (3/4 in) in length, into the access hole of the ignition lock cylinder.
  14. Turn the ignition lock cylinder to START.
  15. Use the bent tip in order to push down on the ignition lock cylinder retainer.
  16. Release the ignition lock cylinder to the RUN position.

  17. Object Number: 375305  Size: SH
  18. Remove the ignition lock cylinder from the lock cylinder case.

Installation Procedure

  1. Insert the ignition lock cylinder through the trim cover in the upper steering column.
  2. Align the lock cylinder retaining tab and the position tab with the slots in the lock housing.

  3. Object Number: 375309  Size: SH
  4. Completely push the lock cylinder into the lock housing.
  5. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  6. Install the retaining screws to the upper steering trim cover.
  7. Tighten
    Tighten the screws to 3.5 N·m (31 lb in).

  8. Match the tab slots on the lower trim cover with the locking tabs on the upper trim cover.
  9. Tilt the lower trim cover up and slide the lower trim cover until the locking tabs snap into the tab slots.
  10. Install the lower trim cover screws to the steering column.
  11. Tighten
    Tighten the screws to 1.5 N·m (13 lb in).


    Object Number: 777650  Size: SH
  12. Install the tilt lever close out plate.
  13. Install the steering wheel. Refer to Steering Wheel Replacement .
  14. Enable the SIR system. Refer to Enabling the SIR System in SIR.
  15. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.