Headlamp Assembly or Headlamp Bulb Replacement Rendezvous

Caution: Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury:

•	Turn off the lamp switch and allow the bulb to cool before changing the bulb.

•	Leave the lamp switch OFF until the bulb change is complete.

•	Always wear eye protection when changing a halogen bulb.

•	Handle the bulb only by its base. Avoid touching the glass.

•	Keep dirt and moisture off the bulb.

•	Properly dispose of the used bulb.

•	Keep halogen bulbs out of the reach of children.

1. Open the hood.
2. Remove the thumb screw from the back of the headlamp.



3. Release the headlamp retainer by lifting up.



4. Pull the headlamp straight forward, to release the ball stud from the grommet.
5. Remove the headlamp from the upper fascia support.
6. Disconnect the electrical connector from the headlamp.



7. Remove the bulb(s) from the headlamp by rotating counterclockwise.



8. Release the headlamp trim tabs from the headlamp, if required.



9. Remove the headlamp trim from the headlamp, pulling to release the adhesive tape.
10. Clean adhesive from the headlamp trim and headlamp using 3M™ adhesive remover P/N 8984, or equivalent.

1. Install new adhesive tape 3M™ P/N 6382 or equivalent to the headlamp trim, if necessary.
2. Position the headlamp trim to the headlamp, if removed.



3. Install the headlamp trim to the headlamp, pressing until end tabs are fully seated.



4. Install the headlamp bulb(s) to the headlamp by rotating clockwise.




Important: The headlamp electrical connector must be positioned into the upper fascia support panel for proper seating of the headlamp.

5. Connect the electrical connector to the headlamp.
6. Position the headlamp to the upper fascia support.
7. Press the headlamp into the upper fascia support until the ball stud is fully seated.



8. Install the thumb screw to the rear of the headlamp.
9. Engage the headlamp vertical retainer, by sliding downward until fully seated.
10. Check the headlamp aim, if a new headlamp was installed, or if service or repairs in the front end area were made. Refer to Headlamp Aiming .
11. Close the hood.

Headlamp Assembly or Headlamp Bulb Replacement Aztek

Caution: Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury:

•	Turn off the lamp switch and allow the bulb to cool before changing the bulb.

•	Leave the lamp switch OFF until the bulb change is complete.

•	Always wear eye protection when changing a halogen bulb.

•	Handle the bulb only by its base. Avoid touching the glass.

•	Keep dirt and moisture off the bulb.

•	Properly dispose of the used bulb.

•	Keep halogen bulbs out of the reach of children.

1. Open the hood.
2. Disconnect the headlamp retainer, by pulling up.



3. Pull the headlamp from the lower center corner, in order to release the ball studs from the grommet retainers.



4. Remove the headlamp from the upper fascia support.



5. Disconnect the electrical connector from the headlamp.
6. Remove the headlamp from the vehicle.



7. Remove the rubber access cover from the headlamp for the bulb you are replacing, if required.



8. Remove the headlamp bulb from the socket, turning counterclockwise.



9. Remove the headlamp bulb from the socket, if required.

1. Install the headlamp bulb into the socket, if required.

Press into place until fully seated.




2. Install the headlamp bulb to the socket, turning clockwise.



3. Install the rubber access cover to the headlamp for the bulb you are replacing, if required.



4. Connect the electrical connector to the headlamp.




Important: The headlamp electrical connector must be positioned into the upper fascia support panel for proper seating of the headlamp.

5. Position the headlamp electrical connector into the access hole in the upper fascia support.



6. Position the headlamp vertical retainer into the slot.
7. Position the headlamp retainer through hole in the upper fascia support.
8. Position the headlamp ball studs into the grommet retainers.



9. Position the headlamp rubber outer seal to properly fit into the front bumper fascia.
10. Press the headlamp into place until fully seated.
11. Inspect the headlamp for proper fit.



12. Install the headlamp vertical retainer, by sliding downward until fully seated.
13. Check the headlamp aim, if a new headlamp was installed, or if service or repairs in the front end area were made. Refer to Headlamp Aiming .
14. Close the hood.