Catalytic Converter Replacement 3.1L

Important: The 3-way catalytic converter is serviced by replacing the entire assembly. Always replace the gaskets at the front and rear flanges when servicing the 3-way catalytic converter. Never reinstall the original gasket.

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
2. Disconnect the heated oxygen sensor (HO2S) electrical connector and retainers. Refer to Heated Oxygen Sensor 2 Replacement in Engine Controls-3.1L.

Notice: Refer to Catalytic Converter Movement Notice in the Preface section.

3. Support the exhaust system.



4. Remove the catalytic converter hangers.



5. Remove the catalytic converter bolts.
6. Remove the catalytic converter gasket.



7. Remove the exhaust manifold pipe stud nuts.
8. Remove the 3-way catalytic converter.



9. Remove the exhaust manifold pipe gasket.



10. Remove the heated oxygen sensor (HO2S). Refer to Heated Oxygen Sensor 2 Replacement in Engine Controls-3.1L.

1. Install the heated oxygen sensor (HO2S). Refer to Heated Oxygen Sensor 2 Replacement in Engine Controls- 3.1L.



2. Install a new exhaust manifold pipe gasket.




Notice: To prevent internal damage to the flexible coupling of the catalytic converter assembly, the converter must be supported. The vertical movement at the rear of the catalytic converter assembly must not exceed 6 degrees up or down.

3. Install and support the 3-way catalytic converter.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the exhaust manifold pipe stud nuts.

Tighten
Tighten the nuts to 35 N·m (26 lb ft).




5. Install the catalytic converter gasket.
6. Install the catalytic converter bolts.

Tighten
Tighten the bolts to 45 N·m (33 lb ft).




7. Install the catalytic converter hangers.
8. Remove the support from the exhaust system.
9. Connect the heated oxygen sensor (HO2S) electrical connector and retainers. Refer to Heated Oxygen Sensor 2 Replacement in Engine Controls - 3.1L.
10. Inspect the exhaust system for leaks and underbody contact.
11. Lower the vehicle.

Catalytic Converter Replacement 3.8L

Important: The 3-way catalytic converter is serviced by replacing the entire assembly. Always replace the gaskets at the front and rear flanges when servicing the 3-way catalytic converter assembly. Never reinstall the original gasket.

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
2. Disconnect the heated oxygen sensor (HO2S) wiring harness connector and retainers. Refer to Heated Oxygen Sensor 2 Replacement in Engine Controls - 3.8L.

Notice: Refer to Catalytic Converter Movement Notice in the Preface section.

3. Support the exhaust system.



4. Remove the catalytic converter hangers.



5. Remove the catalytic converter bolts.
6. Remove the catalytic converter gasket.



7. Remove the exhaust manifold pipe stud nuts.
8. Remove the 3-way catalytic converter.
9. Remove the exhaust manifold pipe gasket at the exhaust manifold pipe studs.



10. Remove the heated oxygen sensor (HO2S). Refer to Heated Oxygen Sensor 2 Replacement in Engine Controls-3.8L.

1. Install the heated oxygen sensor (HO2S). Refer to Heated Oxygen Sensor 2 Replacement in Engine Controls-3.8L.



2. Install a new exhaust manifold pipe gasket to the exhaust manifold pipe studs.

Notice: Refer to Catalytic Converter Movement Notice in the Preface section.

3. Install and support the 3-way catalytic converter.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the exhaust manifold pipe stud nuts.

Tighten
Tighten the nuts to 35 N·m (26 lb ft).




5. Install the catalytic converter gasket.
6. Install the catalytic converter bolts.

Tighten
Tighten the bolts to 45 N·m (33 lb ft).




7. Install the catalytic converter hangers.
8. Connect the heated oxygen sensor (HO2S) electrical connector and retainers. Refer to Heated Oxygen Sensor 2 Replacement in Engine Controls - 3.8L.
9. Remove the support from the exhaust system.
10. Inspect the exhaust system for leaks and underbody contact.
11. Lower the vehicle.