GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 2006 🢒 Rainier - 2WD 🢒 Body 🢒 Exterior Trim 🢒 Front Fog Lamp Replacement

Front Fog Lamp Replacement Rainier

Removal Procedure

    Object Number: 742552 Size: SH
  1. Remove the fog lamp bulb and socket (2). Refer to Front Fog Lamp Bulb Replacement .

    2. Important: The fog lamp bracket is permanently attached to the fascia. Do not remove the fog lamp bracket from the fascia, replace only the fog lamp.


    Object Number: 743216 Size: SH
  2. Remove the 2 push-pins (1) that retain the fog lamp to the fog lamp bracket.
  3. Remove the aim adjustment screw (2) from the fog lamp.
  4. Remove the fog lamp from the fog lamp bracket.

Installation Procedure

    Object Number: 743216 Size: SH
  1. Position the fog lamp to the fog lamp bracket.
  2. Install the 2 push-pins (1) that retain the fog lamp to the fog lamp bracket.
  3. Install the aim adjustment screw (2) to the fog lamp.

    4. Object Number: 742552 Size: SH
  4. Install the fog lamp bulb and socket (2). Refer to Front Fog Lamp Bulb Replacement .
  5. Aim the fog lamp(s). Refer to Fog Lamp Aiming .

Front Fog Lamp Replacement TrailBlazer SS


Object Number: 1670463 Size: SF

Callout

Component Name

Notice: Refer to Fastener Notice in the Preface section.

Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .

Preliminary Procedures

  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Reposition the lower radiator air baffle in order to access the fog lamp adjuster bolts.
  3. Disconnect the electrical connector from the fog lamp bulb socket.

1

Front Fog Lamp Adjuster Bolts

Tip
Remove the 2 horizontal adjusting bolts from the fog lamp bracket assembly.

Tighten
10 N·m (89 lb in)

2

Front Fog Lamp Bracket Retention Clips

Tip
Release the clips in order to remove the housing from the bracket.

3

Fog Lamp Housing

Tip

    • Upon reassembly, ensure the housing is secure to the retention clips on the fog lamp bracket.
    • Aim the fog lamps after replacement. Refer to Fog Lamp Aiming .

Front Fog Lamp Replacement Envoy, TrailBlazer

Removal Procedure
  1. Remove the fog lamp bulb and socket. Refer to Front Fog Lamp Bulb Replacement .

    2. Object Number: 742553 Size: SH
  2. Remove the 3 nuts that retain the fog lamp to the fascia (2).
  3. Remove the fog lamp from the fascia.

Installation Procedure

    Object Number: 742553 Size: SH
  1. Install the fog lamp to the fascia (2).

    2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the 3 fog lamp retaining nuts.

    3. Tighten
    Tighten the nuts to 10.0 N·m (88 lb in).

  3. Install the fog lamp bulb and socket. Refer to Front Fog Lamp Bulb Replacement .
  4. Aim the fog lamp(s). Refer to Fog Lamp Aiming .