GM Service Manual Online
For 1990-2009 cars only

Step

Action

Yes

No

Schematic Reference: Driver Seat Schematics

Connector End View Reference: Power Seat Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

Operate the recline adjuster switch in forward and rearward directions.

Does the recline adjuster motor operate normally?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

3

  1. Install a scan tool.
  2. Observe the Recline Position Switch parameter in the seat module Inputs/Outputs data list.
  3. Operate the recline adjuster switch in the forward direction.

Does the scan tool display the correct switch status parameter in relation to the actual switch position?

Go to Step 4

Go to Step 5

4

Operate the recline adjuster switch in the rearward direction.

Does the scan tool display the correct switch status parameter in relation to the actual switch position?

Go to Step 7

Go to Step 6

5

  1. Disconnect the seat adjuster switch connector.
  2. Connect a 3-amp fuse jumper wire between the battery voltage supply circuit terminal and the recline forward switch signal circuit terminal in the harness connector.
  3. Observe the Recline Position Switch parameter in the seat module Inputs/Outputs data list.

Does the scan tool display the Recline Position Switch parameter as forward?

Go to Step 12

Go to Step 8

6

  1. Disconnect the seat adjuster switch connector.
  2. Connect a 3-amp fuse jumper wire between the battery voltage supply circuit terminal and the recline rearward switch signal circuit terminal in the harness connector.
  3. Observe the Recline Position Switch parameter in the seat module Inputs/Outputs data list.

Does the scan tool display the Recline Position Switch parameter as rearward?

Go to Step 12

Go to Step 9

7

  1. Disconnect the recline adjuster motor control circuit connector.
  2. Connect a test lamp between the control circuit terminals in the harness connector.
  3. Operate the recline adjuster switch in both directions.

Does the test lamp illuminate in the forward and rearward switch positions only?

Go to Step 11

Go to Step 10

8

Test the recline forward switch signal circuit for an open or short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 13

9

Test the recline rearward switch signal circuit for an open or short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 13

10

Test the recline adjuster motor control circuits for an open or short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 13

11

Inspect for poor connections at the recline adjuster motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 14

12

Inspect for poor connections at the seat adjuster switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 15

13

Inspect for poor connections at the seat module. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 16

14

Replace the recline adjuster motor. Refer to Power Seat Adjuster Mechanism Replacement .

Is the repair complete?

Go to Step 17

--

15

Replace the seat adjuster switch. Refer to Power Seat Switch Replacement .

Is the repair complete?

Go to Step 17

--

16

Replace the seat module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Is the repair complete?

Go to Step 17

--

17

Operate the system to verify the repair.

Did you correct the condition?

System OK

Go to Step 2