Step | Action | Value(s) | Yes | No | ||
|---|---|---|---|---|---|---|
Schematic Reference: Inside Rearview Mirror Schematics Component End View Reference: Stationary Windows Connector End Views | ||||||
1 | Did you review the operation of the automatic day-night feature of the mirrors and perform the necessary inspections? | -- | Go to Step 2 | |||
2 |
Does the driver outside rearview mirror remain in a darken state? | -- | Go to Step 22 | Go to Step 3 | ||
3 |
Does the inside rearview mirror darken? | -- | Go to Step 4 | Go to Step 5 | ||
4 | While shining a bright light into the sensor on the mirror face, facing the rear window, observe the driver outside rearview mirror. Does the driver outside rearview mirror darken? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 9 | ||
5 |
Is the resistance less than the specified value? | 3 ohms | Go to Step 6 | Go to Step 20 | ||
6 |
Is the voltage within the specified range? | B+ | Go to Step 7 | Go to Step 21 | ||
7 |
Is the voltage less than the specified value? | 0.5 V | Go to Step 8 | Go to Backup Lamps Always On in Lighting Systems | ||
8 |
Is the voltage within the specified range? | B+ | Go to Step 16 | Go to Step 13 | ||
9 |
Is the voltage within the specified range? | 0.75-1.5 V | Go to Step 11 | Go to Step 10 | ||
10 | Measure the voltage between the automatic day-night signal circuit of the driver outside mirror element and a good ground. Is the voltage within the specified range? | 0.75-1.5 V | Go to Step 15 | Go to Step 14 | ||
11 |
Does the driver outside rearview mirror darken? | -- | Go to Step 17 | Go to Step 12 | ||
12 |
Is the voltage within the specified range? | 0.75-1.5 V | Go to Step 18 | Go to Step 19 | ||
13 | Test the backup lamp supply voltage circuit of the inside rearview mirror for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 27 | Go to Backup Lamps Inoperative in Lighting Systems | ||
14 | Test the automatic day-night signal circuit of the driver outside rearview mirror element for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 27 | Go to Step 16 | ||
15 | Test the low reference circuit of the driver outside rearview mirror element for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 27 | Go to Step 16 | ||
16 | Inspect for poor connections at the harness connector of the inside rearview mirror. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 27 | Go to Step 23 | ||
17 | Inspect for poor connections at the harness connector of the DDM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 27 | Go to Step 24 | ||
18 | Inspect for poor connections at the harness connector of the driver outside rearview mirror face. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 27 | Go to Step 25 | ||
19 | Inspect for poor connections at the harness connector of the driver outside rearview mirror. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 27 | Go to Step 26 | ||
20 | Repair an open or high resistance in the ground circuit of the inside rearview mirror. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 27 | -- | ||
21 | Repair an open or short to ground in the ignition voltage circuit of the inside rearview mirror. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 27 | -- | ||
22 |
Important:: A short to voltage on the automatic day-night signal circuit of the driver outside rearview mirror element will cause permanent damage to the driver outside rearview mirror and the inside rearview mirror. Both mirrors will have to replaced. The following actions will need to be performed:
Important: Perform the Compass Calibration and Magnetic Variance for the inside rearview mirror with compass.
Did you complete the repair? | -- | Go to Step 27 | -- | ||
23 |
Important: Perform the Compass Calibration and Magnetic Variance for the inside rearview mirror with compass. Replace the inside rearview mirror. Refer to Inside Rearview Mirror Replacement . Did you complete the replacement? | -- | Go to Step 27 | -- | ||
24 | Replace the DDM. Refer to Door Control Module Replacement - Front . Is the replacement complete? | -- | Go to Step 27 | -- | ||
25 | Replace the driver outside rearview mirror face. Refer to Outside Rearview Mirror Glass Replacement . Did you complete the replacement? | -- | Go to Step 27 | -- | ||
26 | Replace the driver outside rearview mirror. Refer to Power Mirror Replacement . Did you complete the replacement? | -- | Go to Step 27 | -- | ||
27 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 2 | ||
