GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B1AA2: Passenger Seat Cushion Temperature Sensor Circuit Open

DTC B1AA3: Passenger Seat Back Temperature Sensor Circuit Open

DTC B272B: Passenger Seat Back Over Temperature

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

B+

1

1

--

--

Ignition Voltage

1

1

--

--

Passenger Seat Blower Supply Voltage

B111D

B272F

B272F

--

Passenger Seat Back Blower Supply Voltage

B111D

B272D, B727B, B272F

B272F

--

Passenger Seat Cushion Blower Supply Voltage

B111D

B272A, B272D

B272F

--

Passenger Heated Seat Back Only Mode Switch Signal

5

5

5

--

Passenger Heated Seat Cool Switch Signal

4

4

4

--

Passenger Seat Back Cushion Switch Signal

3

3

3

--

Passenger Seat Back Temperature Sensor Signal

B272B, B272D

B1AA3, B272D

B1AA3, B272D

--

Passenger Seat Cushion Temperature Sensor Signal

B272A, B272D

B1AA2, B272D

B1AA2, B272D

--

Right Heated/Cooled Seat Mode Signal

2

2

2

--

Passenger Seat Back Heated/Cool Ventilation Module Cool Control

B111A

B272D, 4

--

--

Passenger Seat Back Heated/Cool Ventilation Module Heat Control

B111A, 4

B272D, 4, 5

--

--

Passenger Seat Cushion Heated/Cool Ventilation Module Cool Control

B111A

B272D, 4

--

--

Passenger Seat Cushion Heated/Cool Ventilation Module Heat Control

B111A, 4

B272D

4

--

Passenger Seat Back Blower Speed Control

B19A6

B272B, B272D, B272F

B19A2

--

Passenger Seat Cushion Blower Speed Control

B19A5

B272A, B272D

B19A1

--

Low Reference - Passenger Heated Seat Switch

--

2

--

--

Low Reference - Passenger Seat Back Blower

--

B272B, B272D, B272F

--

--

Low Reference - Passenger Seat Back and Cushion Blower

--

B272F

--

--

Low Reference - Passenger Seat Cushion Blower

--

B272A, B272D

--

--

Low Reference - Passenger Seat Back Temperature Sensor

--

B1AA3, B272D

--

--

Low Reference - Passenger Seat Cushion Temperature Sensor

--

B1AA2, B272D

--

--

Ground - Climate Control Seat Module

--

1

--

--

1. Driver and passenger heated/cooled seats are inoperative

2. Driver seat heat and cool modes are inoperative

3. Seat heat mode is inoperative

4. Seat cool mode is inoperative

5. Heated/cooled seat inoperative - Back Only Mode

Circuit/System Description

The heat and cool seat functions for the driver and passenger seats are controlled by the climate control seat module (CCSM) that is located under the passenger seat cushion. When a driver or passenger heat or cool seat switch is pressed, a low reference signal is applied through the switch signal circuit to the door control module. In response to the switch input, the door module sends a serial data message to the memory seat module (MSM) indicating the heat/cool seat request. The MSM then sends a pulse width modulation (PWM) signal through the heated/cooled seat mode signal circuit to the CCSM. The CCSM then applies battery positive voltage to the seat cushion and seat back thermal electronic devices (TEDs) and a pre-determined voltage to the blower motors. To determine seat temperature, the CCSM supplies a 5-volt signal and a low reference to the temperature sensors that are attached to each TED. The temperature sensors are variable resistors, their resistance changes as the temperature of the seat changes. Then based on the seat temperature, the CCSM controls the voltage level that it applies to the TEDs and blower motors.

Conditions for Running the DTC

Ignition ON and the passenger heat or cool seat is commanded On.

Conditions for Setting the DTC

B1AA2

The CCSM detects the passenger seat cushion temperature sensor voltage is greater than 4.73 volts or 242 counts for more than 4 seconds.

B1AA3

The CCSM detects the passenger seat back temperature sensor voltage is greater than 4.73  volts or 242 counts for more than 4 seconds.

B272B

    • The CCSM detects an open in the seat cushion blower speed control circuit.
    • The CCSM detects the passenger seat back temperature sensor voltage is less than 0.5 volts or 20 counts for more than 4 seconds.

Action Taken When the DTC Sets

The CCSM will disable the heat or cool seat function for the current ignition cycle.

Conditions for Clearing the DTC

The current DTC clears when the malfunction is no longer present and the power mode changes to OFF then back to ACC or RUN.

Diagnostic Aids

In order to perform valid tests when diagnosing the climate control seat (CCS) system, the ignition must be cycled OFF then ON between each test in order to reset the CCSM.

Reference Information

Schematic Reference

Heated/Cooled Seat Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Heated/Cooled Seats Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit System Verification

  1. Ignition ON, verify the scan tool Seat 2 Cushion Temp parameter is between 0.5-4.73 volts.
  2. If not within the specified range, refer to B1AA2 - Seat Cushion Temperature Sensor Test.
  3. Verify the scan tool Seat 2 Back Temp parameter is between 0.5-4.73 volts.
  4. If not within the specified range, refer to B1AA3, B272B - Seat Back Temperature Sensor and Blower Test.
  5. If the seat cushion and back temperature parameters displayed correctly on the scan tool, refer to the B1AA3, B272B - Seat Back Temperature Sensor and Blower Test.

Circuit/System Testing

B1AA2 - Seat Cushion Temperature Sensor Test

  1. Ignition OFF, disconnect the X2 harness connector at the CCSM.
  2. Important: If the resistance is measured with the seat still warm or cool, the resistance values will vary. At 68°F (20°C), the nominal resistance value is 1200 ohms ±5 percent. For warmer or cooler ambient temperatures, refer to the Temperature vs Resistance table below. The delta resistance values between the seat cushion and seat back temperature sensors should not be greater than 2000 ohms.

  3. Test for 300 ohms-18K ohms between the signal circuit terminal 2 and the low reference circuit terminal 3.
  4. If greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits test normal, test or replace the seat cushion ventilation heat and cool module.
    If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, test or replace the seat cushion ventilation heat and cool module.
  5. Connect the X2 harness connector at the CCSM.
  6. Disconnect the harness connector at the seat cushion ventilation heat and cool module.
  7. Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal 5 and ground.
  8. If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the CCSM.
    If less than the specified range, test the signal circuit for a short to ground. If the circuits tests normal, replace the CCSM.
  9. If all circuits test normal, replace the CCSM.

B1AA3, B272B - Seat Back Temperature Sensor and Blower Test

  1. Ignition OFF, disconnect the X2 harness connector at the CCSM.
  2. Important: If the resistance is measured with the seat still warm or cool, the resistance values will vary. At 68°F (20°C), the nominal resistance value is 1200 ohms ±5 percent. For warmer or cooler ambient temperatures, refer to the Temperature vs Resistance table below. The delta resistance values between the seat cushion and seat back temperature sensors should not be greater than 2000 ohms.

  3. Test for 300 ohms-18K ohms between the signal circuit terminal 4 and the low reference circuit terminal 5.
  4. If greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits test normal, test or replace the seat cushion ventilation heat and cool module.
    If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, test or replace the seat cushion ventilation heat and cool module.
  5. Connect the X2 harness connector at the CCSM.
  6. Disconnect the harness connector at the seat back ventilation heat and cool module.
  7. Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal 5 and ground.
  8. If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the CCSM.
    If less than the specified range, test the signal circuit for a short to ground. If the circuits tests normal, replace the CCSM.
  9. Connect a test lamp between the control circuit terminal 2 and ground.
  10. Ignition ON, command the Passenger Seat Blower Cmd. ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
  11. If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit test normal, replace the CCSM.
  12. Connect a test lamp between the control circuit terminal 7 and ground.
  13. Ignition ON, command the Passenger Seat Blower Cmd. ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
  14. If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit test normal, replace the CCSM.
  15. If all circuits test normal, test or replace the seat back ventilation heat and cool module.

Component Testing

Ventilation Heat and Cool Module

  1. Ignition OFF, disconnect the harness connectors at the seat cushion and seat back ventilation heat and cool modules.
  2. Important: If the resistance is measured with the seat still warm or cool, the resistance values will vary. At 68°F (20°C), the nominal resistance value is 1200 ohms ±5 percent. For warmer or cooler ambient temperatures, refer to the Temperature vs Resistance table below. The delta resistance values between the seat cushion and seat back temperature sensors should not be greater than 2000 ohms.

  3. Test for 300 ohms-18K ohms between the temperature sensor signal circuit terminal 5 and the low reference circuit terminal 8.
  4. If not within the specified range, replace the ventilation heat and cool module.

    Important: The test leads must be connected in the correct polarity, otherwise lower out of range values will appear. Use the Positive Lead for the COOL control circuit and the Negative Lead for the HEAT control circuit. If the resistance is measured with the seat still warm or cool, the resistance values will vary even if the system was powered up for just a few seconds. The TED must be allowed to stabilize to room temperature prior to a measurement. The following conditions will change the resistance to out of range values:

       • The test leads are incorrectly connected.
       • Air blowing across the TED
       • Measuring the resistance at other than room temperature of 70°F
       • Holding the TED portion of the heated and cool ventilation module in your hand
    In warmer or cooler climates where room temperature conditions of 70°F (21°C) may be unattainable, resistance values may read above the specified range. Use a heat gun or a blower to warm or cool the TED while measuring the resistance. The resistance values should slowly lower toward the specified range.

  5. Test for 0.9-10.0 ohms between the heat control circuit terminal 1 and the cool control circuit terminal 3.
  6. If not within the specified range, replace the ventilation heat and cool module.

    Important: The test leads must be connected in the correct polarity, otherwise higher out of range values will appear. Use the Positive Lead for the control circuit and the Negative Lead for the ground circuit.

  7. Test for 6-9K ohms between blower motor control circuit terminal 2 and the low reference circuit terminal 4.
  8. If not within the specified range, replace the ventilation heat and cool module.

    Important: The test leads need to be connected in the correct polarity, otherwise higher out of range values will appear. Use the Positive Lead for the speed control circuit and the Negative Lead for the ground circuit.

  9. Test for 290-420K ohms between blower motor speed control circuit terminal 7 and the low reference circuit terminal 4.
  10. If not within the specified range, replace the ventilation heat and cool module.

Temperature vs Resistance

°C

°F

OHMS

Temperature vs Resistance Values (Approximate)

60°

140°

319.9

50°

122°

433.1

40°

104°

596.6

30°

86°

837.5

20°

68°

1200

10°

50°

1757

32°

2633

-10°

14°

4047

-20°

-4°

6401

-30°

-22°

10,450

-40°

-40°

17,670

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Driver or Passenger Seat Back Ventilation Heating and Cooling Blower Replacement
    •  Driver or Passenger Seat Cushion Ventilation Heating and Cooling Blower Replacement
    •  Control Module References for CCSM replacement, setup, and programming