GM Service Manual Online
For 1990-2009 cars only

DTC Descriptor

DTC P0451: Fuel Tank Pressure (FTP) Sensor Performance

Diagnostic Fault Information

Important: Always perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

FTP Sensor Low Reference

--

P0446, P0451

P0446

--

P0451

FTP Sensor Signal

P0452

--

P0452

P0453

P0451, P0454

FTP Sensor 5-Volt Reference

P0452, P0530, P0641

P0451

P0446, P0453

P0453, P0530, P0641

--

Typical Scan Tool Data

FTP Sensor Voltage

Circuit¹

Normal Range

Short to Ground

Open

Short to Voltage

FTP Sensor Low Reference

--

1.5 V

4.5 V

--

FTP Sensor Signal

1.5 V

0 V

0 V

5 V

FTP Sensor 5-Volt Reference

0 V

0 V

5 V

¹ With EVAP system vented to atmosphere

Circuit/System Description

The fuel tank pressure (FTP) sensor measures air pressure or vacuum in the evaporative emission (EVAP) system. The control module supplies a 5-volt reference and a low reference circuit to the FTP sensor. The FTP sensor signal voltage varies depending on EVAP system pressure or vacuum. The controller also uses this FTP signal to determine atmospheric pressure for use in the engine-off small leak test, DTC P0442. Before using this signal as an atmospheric reference it must first be re-zeroed.

Conditions for Running the DTC

    • DTC P0451 runs only when the engine-off natural vacuum small leak test, DTC P0442, executes.
    • The number of times this test runs can range from 0-2 per engine-off period. The length of the test can be up to 10 minutes.

Conditions for Setting the DTC

This DTC will set if the controller is unable to re-zero the FTP sensor voltage within a calibrated range during the engine-off small leak test, DTC P0442.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame/Failure Records.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids

    • A restriction in the EVAP canister or vent lines could prevent fuel vapor pressure from bleeding off fast enough. If the vent system cannot bleed off pressure fast enough, the re-zero procedure may not complete successfully, which could cause this code to set. By using the purge solenoid command on a scan tool, vacuum can be applied to the system instead of pressure. With the EVAP canister vent solenoid valve open and the EVAP canister purge solenoid valve commanded to 100 percent, the vacuum should not increase to more than 9 inches H2O.
    • Ensure that the reference port on the FTP sensor is unobstructed.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

    •  Engine Control Module Connector End Views
    •  Engine Controls Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Troubleshooting with a Test Lamp
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

    •  Scan Tool Data List
    •  Scan Tool Output Controls

Special Tools Required

J 41413-200 Evaporative Emission System Tester (EEST)

Circuit/System Verification

  1. If DTCs P0452, P0453, or P0641 are set, repair those first.
  2. With a scan tool, command the EVAP canister vent solenoid valve closed.
  3. Command the purge solenoid to 20 percent.
  4. Observe the FTP sensor voltage parameter as the vacuum increased to the abort limit.
  5. The voltage should scale smoothly.

Circuit/System Testing

    Important: Refer to the J 41413-200 operation manual for detailed instructions.

  1. Start the engine with the J 41413-200 connected to the fuel filler neck.
  2. Allow the engine to idle.
  3. Use the Purge/Seal function to seal the system with a scan tool.
  4. Command the EVAP canister purge solenoid valve to 20 percent.
  5. Observe the vacuum/pressure gage on the J 41413-200 and the FTP parameter on the scan tool.
  6. Allow the vacuum to increase on the gage of the J 41413-200 until it reaches approximately 16 inches H2O, or until the vacuum reached the abort limit on the scan tool.
  7. Use the Purge/Seal function to seal the system with a scan tool.
  8. If the difference between the FTP parameter on a scan tool and the vacuum/pressure gage on the J 41413-200 is more than 1 inch H2O, replace the FTP sensor.
  9. If the Fuel Tank Pressure Sensor parameter on a scan tool display is less than 3.2 volts, replace the FTP sensor.

Repair Instructions

Important: Always perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Fuel Tank Pressure Sensor Replacement
    •  Control Module References for ECM replacement, setup, and programming