GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P0106: Manifold Absolute Pressure (MAP) Sensor Performance

Diagnostic Fault Information

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

5-Volt Reference

P0107, P0452, P0532, P0641

P0106, P0107

P0107

P0106, P0108, P0453, P0533, P0641

P0106, P1101

MAP Sensor Signal

P0107

P0106, P0107

P0107

P0108

P0106, P1101

Low Reference

--

P0106, P0108

P0106, P0108

--

P0106, P1101

Typical Scan Tool Data

MAP Sensor

Circuit

Short to Ground

Open or High Resistance

Short to Voltage

Operating Conditions: Engine running.

Normal MAP Parameter: 12-103 kPa

5-Volt Reference

10 kPa

10 kPa

104 kPa

MAP Sensor Signal

10 kPa

10 kPa

104 kPa

Low Reference

--

90-104 kPa¹

--

¹Varies depending on ECM version

Circuit Description

The intake flow rationality diagnostic provides the within-range rationality check for the mass air flow (MAF), manifold absolute pressure (MAP), and the throttle position (TP) sensors. This is an explicit model-based diagnostic containing 4 separate models for the intake system.

    • The throttle model describes the flow through the throttle body and is used to estimate the MAF through the throttle body as a function of barometric pressure (BARO), TP, intake air temperature (IAT), and estimated MAP. The information from this model is displayed on the scan tool as the MAF Performance Test parameter.
    • The first intake manifold model describes the intake manifold and is used to estimate MAP as a function of the MAF into the manifold from the throttle body and the MAF out of the manifold caused by engine pumping. The flow into the manifold from the throttle uses the MAF estimate calculated from the above throttle model. The information from this model is displayed on the scan tool as the MAP Performance Test 1 parameter.
    • The second intake manifold model is identical to the first intake manifold model except that the MAF sensor measurement is used instead of the throttle model estimate for the throttle air input. The information from this model is displayed on the scan tool as the MAP Performance Test 2 parameter.
    • The fourth model is created from the combination and additional calculations of the throttle model and the first intake manifold model. The information from this model is displayed on the scan tool as the TP Performance Test parameter.

The estimates of MAF and MAP obtained from this system of models and calculations are then compared to the actual measured values from the MAF, MAP, and the TP sensors and to each other to determine the appropriate DTC to fail. The following table illustrates the possible failure combinations and the resulting DTC or DTCs.

Scan Tool Diagnostic Test Results

MAF Performance Test

MAP Performance Test 1

MAP Performance Test 2

TP Performance Test

DTCs Passed

DTCs Failed

--

--

OK

OK

P0101, P0106, P0121, P1101

None

OK

OK

Fault

OK

P0101, P0106, P0121, P1101

None

Fault

OK

Fault

OK

P0106, P0121, P1101

P0101

OK

Fault

Fault

OK

P0101, P0121, P1101

P0106

Fault

Fault

Fault

OK

P0121, P1101

P0101, P0106

--

--

OK

Fault

P0101, P0106, P1101

P0121

OK

OK

Fault

Fault

P0101, P0106, P0121, P1101

None

Fault

OK

Fault

Fault

P0101, P0106, P0121

P1101

--

Fault

Fault

Fault

P0101, P0106, P0121

P1101

Conditions for Running the DTC

    • DTCs P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0116, P0118, P0128, P0335, P0336, P0401, P0405, P1404 are not set.
    • The engine speed is between 500-5,000 RPM.
    • The IAT Sensor parameter is between -7 and +60°C (+19 and +140°F).
    • The ECT Sensor parameter is between 70-129°C (158-264°F).
    • This DTC runs continuously within the enabling conditions.

Conditions for Setting the DTC

The engine control module (ECM) detects that the MAP sensor pressure is not within range of the calculated pressure that is derived from the system of models for more than 0.5 second.

Action Taken When the DTC Sets

DTC P0106 is a Type B DTC.

Conditions for Clearing the MIL/DTC

DTC P0106 is a Type B DTC.

Diagnostic Aids

  1. A skewed or stuck engine coolant temperature (ECT) or IAT will cause the calculated models to be inaccurate and may cause this DTC to run when it should not. Refer to Temperature Versus Resistance .
  2. A skewed MAP sensor will also cause the first and second intake manifold models to disagree with the actual MAP sensor measurements. Use a scan tool and compare the MAP Sensor parameter to a known good vehicle under various operating conditions.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

    •  Engine Controls Connector End Views
    •  Engine Control Module Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

    •  Scan Tool Data Definitions
    •  Scan Tool Data List

Special Tools Required

    • J 23738-A Mityvac
    • J 35555 Metal Mityvac

Circuit/System Verification

  1. Verify that P0641 or P0651 are not set.
  2. If any of the DTCs are set, refer to DTC P0641 or P0651 .
  3. Verify that restrictions do not exist in the exhaust system. Refer to Restricted Exhaust .
  4. Verify that the engine is in good mechanical condition. Refer to Symptoms - Engine Mechanical .
  5. Ignition OFF for 90 seconds, determine the current vehicle testing altitude. Ignition ON, observe the scan tool MAP Sensor parameter. Compare the parameter to the Altitude Versus Barometric Pressure table. The MAP Sensor parameter should be within the specified range indicated in the table.
  6. A skewed MAP sensor will also cause the first and second intake manifold models to disagree wit the actual MAP sensor measurements. Use the scan tool and compare the MAP Sensor parameter to a known good vehicle, under various operating conditions. The readings should be within 3 kPa of the known good vehicle.
  7. Ignition ON, observe the scan tool MAP sensor parameter. Start the engine. The MAP Sensor parameter should change.
  8. Engine running, observe the DTC information with a scan tool. DTC P0106 should not set.
  9. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

  1. Verify the integrity of the entire air induction system by inspecting for the following conditions:
  2. • Any damaged components
    • Loose or improper installation
    • An air flow restriction
    • Any vacuum leak
    • Improperly routed vacuum hoses
    • In cold climates, inspect for any snow or ice buildup
    • Verify that restrictions do not exist in the MAP sensor port or vacuum source.
  3. Ignition OFF, disconnect the harness connector at the MAP sensor.
  4. Ignition OFF for 90 seconds, test for less than 5 ohms of resistance between the low reference circuit terminal A and ground.
  5. If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
  6. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal C and ground.
  7. If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
    If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.
  8. Verify the scan tool MAP parameter is less than 12 kPa.
  9. If greater than the specified range, test the signal circuit terminal B for a short to voltage. If the circuit tests normal, replace the ECM.
  10. Install a 3A fused jumper wire between the signal circuit terminal B and the 5-volt reference circuit terminal C. Verify the scan tool MAP parameter is greater than 103 kPa.
  11. If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
  12. If all circuits test normal, test or replace the MAP sensor.

Component Testing

Important: You must perform the Circuit/Testing in order to verify the integrity of the MAP sensor circuits before proceeding with the Component Testing.

Skewed Signal Test

  1. Ignition OFF, remove the vacuum source from the MAP sensor.
  2. Ignition ON, observe and record the scan tool MAP sensor pressure parameter. This is the first MAP sensor reading.
  3. With the J 23738-A or J 35555 , apply 5 in Hg (17 kPa) of vacuum to the MAP sensor. Observe and record the scan tool MAP sensor pressure parameter. This is the second MAP sensor reading.
  4. Subtract the second MAP sensor reading from the first MAP sensor reading. Verify that the vacuum decrease is within 1 in Hg (4 kPa) of the applied vacuum.
  5. If the vacuum decrease is not within the specified range, replace the MAP sensor.
  6. With the J 23738-A or J 35555 , apply 10 in Hg (34 kPa) of vacuum to the MAP sensor. Observe and record the scan tool MAP sensor pressure parameter. This is the third MAP sensor reading.
  7. Subtract the third MAP sensor reading from the first MAP sensor reading. Verify that the vacuum decrease is within 1 in Hg (4 kPa) of the applied vacuum.
  8. If the vacuum decrease is not within the specified range, replace the MAP sensor.

Erratic Signal Test

  1. Ignition OFF, remove the MAP sensor.
  2. Install a 3A fused jumper wire between the 5-volt reference circuit terminal C and the corresponding terminal of the MAP sensor.
  3. Install a jumper wire between the low reference terminal A of the MAP sensor and ground.
  4. Install a jumper wire at terminal B of the MAP sensor.
  5. Connect a DMM between the jumper wire from the terminal B of the MAP sensor and ground.
  6. Ignition ON, with the J 23738-A or J 35555 , slowly apply vacuum to the sensor while observing the voltage on the DMM. The voltage should vary between 4.9-0.2 volts without any spikes or dropouts.
  7. If the voltage is erratic, replace the MAP sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Manifold Absolute Pressure Sensor Replacement
    •  Control Module References for ECM replacement, setup, and programming