Lumbar Support Inoperative w/o A45
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Driver Seat Schematics or Passenger Seat Schematics Connector End View Reference: Power Seat Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 | Verify that the Lumbar Support Inoperative complaint is present. Does the lumbar support system operate as described in the system description and operation? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 | Measure the voltage from the battery positive voltage circuit of the lumbar switch to a good ground. Does the voltage measure within the specified range? | 9-16 V | Go to Step 4 | Go to Step 6 |
4 | Measure the voltage from the battery positive voltage circuit of the lumbar switch to the ground circuit of the lumbar switch. Does the voltage measure within the specified range? | 9-16 V | Go to Step 5 | Go to Step 7 |
5 | Inspect for poor connections at the harness connector of the lumbar switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 8 |
6 | Repair the open in the battery positive voltage circuit of the lumbar switch. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 9 | -- |
7 | Repair the open in the ground circuit of the lumbar switch. Refer to Wiring Repairs in Wiring Systems. Is the circuit repair complete? | -- | Go to Step 9 | -- |
8 | Replace the lumbar switch. Refer to Lumbar Switch Replacement . Did you complete the replacement? | -- | Go to Step 9 | -- |
9 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 2 |
Lumbar Support Inoperative with A45
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Driver Seat Schematics Connector End View Reference: Power Seat Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 | Verify that the Lumbar Support Inoperative complaint is present. Does the lumbar support system operate as described in the system description and operation? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 |
Did the lumbar parameter change state? | -- | Go to Step 7 | Go to Step 4 |
4 | Measure the voltage from the battery positive voltage circuit of the lumbar switch to a good ground. Does the voltage measure within the specified range? | 9-16 V | Go to Step 5 | Go to Step 8 |
5 |
Does the test lamp illuminate? | -- | Go to Step 7 | Go to Step 6 |
6 | Inspect for poor connections at the harness connector of the lumbar switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 11 | Go to Step 9 |
7 | Inspect for poor connections at the harness connector of the MSM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 11 | Go to Step 10 |
8 | Repair the open in the battery positive voltage circuit of the lumbar switch. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 11 | -- |
9 | Replace the lumbar switch. Refer to Lumbar Switch Replacement . Did you complete the replacement? | -- | Go to Step 11 | -- |
10 | Replace the MSM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 11 | -- |
11 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 2 |
