DTC C1283 Excessive Time to Center Steering w/JL4
Circuit Description
The steering wheel position sensor supplies 2 analog inputs, Phase A and Phase B, to the EBCM. The 2 input signals are approximately 90 degrees out of phase. By interpreting the relationship between the 2 inputs, the EBCM can determine the position of the steering wheel and the direction of steering wheel rotation.
Steer angle centering is the process by which the EBCM calibrates the steering sensor output so that the output reads zero when the steering wheel is centered. Using the yaw rate input, lateral accelerometer input, and wheel speed sensor inputs, the initial steering center position is calculated after driving greater than 10 km/h (6 mph) for more than 10 seconds in a straight line on a level surface.
Conditions for Running the DTC
The vehicle speed is greater than 40 km/h (25 mph).
Conditions for Setting the DTC
The vehicle has driven for 10 minutes without completing steer angle centering.
Action Taken When the DTC Sets
| • | The EBCM disables the VSES for the duration of the ignition cycle. |
| • | The DIC displays the SERVICE STABILITY SYSTEM message. |
| • | The ABS/TCS remains functional. |
Conditions for Clearing the DTC
| • | The condition for the DTC is no longer present and the DTC is cleared with a scan tool. |
| • | The electronic brake control module (EBCM) automatically clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles. |
Diagnostic Aids
| • | During diagnosis, park the vehicle on a level surface. |
| • | Check the vehicle for proper alignment. The car should not pull in either direction while driving straight on a level surface. |
| • | Find out from the driver under what conditions the DTC was set (when the DIC displayed the SERVICE STABILITY SYSTEM message). This information will help to duplicate the failure. |
| • | The Snapshot function on the scan tool can help find an intermittent DTC. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step performs the Steering Position Sensor Test to see if the steering wheel position sensor (SWPS) is operating properly.
-
This step checks to see if the lateral accelerometer input parameter is within the valid range.
-
This step checks to see if the yaw rate input parameter is within the valid range.
Step | Action | Value(s) | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the ABS Diagnostic System Check? | -- | Go to Step 2 | |||||||
Use the scan tool in order to perform the Steering Position Sensor Test in the DRP/ABS/TCS/TIM/VSES Special Functions. Refer to Scan Tool Diagnostics . Did the steering wheel position pass the test? | -- | Go to Step 3 | Go to Step 7 | |||||||
With a scan tool, observe the Lateral Accelerometer Input parameter in the VSES data list. Does the scan tool display within the specified range? | 2.3-2.7 V | Go to Step 4 | Go to Step 8 | |||||||
With a scan tool, observe the Yaw Rate Sensor Input parameter in the VSES data list. Does the scan tool display within the specified range? | 2.3-2.7 V | Go to Step 5 | Go to Step 9 | |||||||
5 |
Does the DTC reset? | -- | Go to Step 6 | Go to Diagnostic Aids | ||||||
6 |
Important: Perform the setup procedure for the EBCM. An unprogrammed EBCM will
result in the following conditions:
Replace the EBCM. Refer to Electronic Brake Control Module Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||
7 | Replace the steering wheel position sensor (SWPS). Refer to Steering Shaft, Lower Bearing, and Jacket - Disassemble - Off Vehicle and Steering Shaft, Lower Bearing, and Jacket - Assemble - Off Vehicle in Steering Wheel and Column - Tilt. Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||
8 | Replace the lateral accelerometer. Refer to Lateral Accelerometer Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||
9 | Replace the yaw rate sensor. Refer to Vehicle Yaw Sensor Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||
10 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
