Remote Control Door Lock Receiver Scan Tool Information. Buick LaCrosse 2008

For 1990-2009 cars only

Makes 🢒 Buick 🢒 2008 🢒 LaCrosse 🢒 Power and Signal Distribution 🢒 Data Communications 🢒 Remote Control Door Lock Receiver Scan Tool Information

Table 1:	Remote Control Door Lock Receiver Scan Tool Data Parameters
Table 2:	RCDLR Scan Tool Output Controls

Remote Control Door Lock Receiver Scan Tool Data Parameters

Parameter	System State	Expected Value	Description
Operating Conditions: Ignition ON
Battery Voltage Signal	--	Varies	The scan tool displays volts. This is the current voltage of the battery voltage signal.
Fob 1 Battery	--	OK	The scan tool displays OK or Low. This is the state of the Fob 1 battery.
Fob 1 Function	--	None	The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. This is the state of the Fob 1 command as monitored by the RCDLR.
Fob 1 Programmed	--	Yes	The scan tool displays Yes or No. Yes is displayed if the Fob 1 is programmed into the RCDLR.
Fob 2 Battery	--	OK	The scan tool displays OK or Low. This is the state of the Fob 2 battery.
Fob 2 Function	--	None	The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. This is the state of the Fob 2 command as monitored by the RCDLR.
Fob 2 Programmed	--	Yes	The scan tool displays Yes or No. Yes is displayed if the Fob 2 is programmed into the RCDLR.
Fob 3 Battery	--	OK	The scan tool displays OK or Low. This is the state of the Fob 3 battery.
Fob 3 Function	--	None	The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. This is the state of the Fob 3 command as monitored by the RCDLR.
Fob 3 Programmed	--	Yes	The scan tool displays Yes or No. Yes is displayed if the Fob 3 is programmed into the RCDLR.
Fob 4 Battery	--	OK	The scan tool displays OK or Low. This is the state of the Fob 4 battery.
Fob 4 Function	--	None	The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. This is the state of the Fob 4 command as monitored by the RCDLR.
Fob 4 Programmed	--	Yes	The scan tool displays Yes or No. Yes is displayed if the Fob 4 is programmed into the RCDLR.
Front Placard	--	Varies	This displays Counts.
Last Fob Used	--	Varies	The scan tool displays None, Fob 1, Fob 2, Fob 3, Fob 4 or Fob 5. This was the last Fob used, as monitored by the RCDLR.
Last Key Pressed on Fob	--	Varies	The scan tool displays Unlock, Lock, Panic, Remote Start, Rear Closure, Left Slide Door, Right Slide Door, and Learn. This was the last key pressed on the fob, as monitored by the RCDLR.
LF Pressure Sensor Mode	--	Varies	The scan tool displays Learn, Re-measure, Off, Stationary, Wakeup, and Learn. This is the state of the left front pressure sensor.
LF Pressure Status	--	Normal	The scan tool displays Unknown, Normal, Low, Low. This is the state of the left front tire pressure.
LF Tire Press. Sensor Status	--	Normal	The scan tool displays Normal Mode, Fault or Low Battery. This is the state of the left front tire pressure sensor.
LF Tire Pressure	--	Varies	This displays kPa (psi). This is the amount of pressure in the left front tire.
LR Pressure Sensor Mode	--	Varies	The scan tool displays Learn, Re-measure, Off, Stationary, Wakeup, and Learn. This is the state of the left rear pressure sensor.
LR Pressure Status	--	Normal	The scan tool displays Unknown, Normal, Low, Low. This is the state of the left rear tire pressure.
LR Tire Press. Sensor Status	--	Normal	The scan tool displays Normal Mode, Fault or Low Battery. This is the state of the left rear tire pressure sensor.
LR Tire Pressure	--	Varies	This displays kPa (psi). This is the amount of pressure in the left rear tire.
Rear Placard	--	Varies	This displays Counts.
RF Pressure Sensor Mode	--	Varies	The scan tool displays Learn, Re-measure, Off, Stationary, Wakeup, and Learn. This is the state of the right front pressure sensor.
RF Pressure Status	--	Normal	The scan tool displays Unknown, Normal, Low, Low. This is the state of the right front tire pressure.
RF Tire Press. Sensor Status	--	Normal Mode	The scan tool displays Normal Mode, Fault or Low Battery. This is the state of the right front tire pressure sensor.
RF Tire Pressure	--	Varies	This displays kPa (psi). This is the amount of pressure in the right front tire.
RR Pressure Sensor Mode	--	Varies	The scan tool displays Learn, Re-measure, Off, Stationary, Wakeup, and Learn. This is the state of the right rear pressure sensor.
RR Pressure Status	--	Normal	The scan tool displays Unknown, Normal, Low, Low. This is the state of the right rear tire pressure.
RR Tire Press. Sensor Status	--	Normal	The scan tool displays Normal Mode, Fault or Low Battery. This is the state of the right rear tire pressure sensor.
RR Tire Pressure	--	Varies	This displays kPa (psi). This is the amount of pressure in the right rear tire.
Selected Front Tire Type	--	Varies	The scan tool displays N/A, P-Metric (S), P-Metric (X), Load Range C, Load Range D or Load Range E. This is the type of front tires used on the vehicle.
Selected Rear Tire Type	--	Varies	The scan tool displays N/A, P-Metric (S), P-Metric (X), Load Range C, Load Range D or Load Range E. This is the type of rear tires used on the vehicle.
TPM System Enabled	--	Yes	The scan tool displays Yes or No. Yes is displayed if the TPM system is enabled.

RCDLR Scan Tool Output Controls

Output Control	Description
Invalidate All Fobs	This program will erase all key fobs from memory and then begin reprogramming
Program Key Fob 1	Place module in program mode Repeatedly press and hold the Lock/Unlock buttons on the key fob.
Program Key Fob 2	Place module in program mode Repeatedly press and hold the Lock/Unlock buttons on the key fob.
Program Key Fob 3	Place module in program mode Repeatedly press and hold the Lock/Unlock buttons on the key fob.
Program Key Fob 4	Place module in program mode Repeatedly press and hold the Lock/Unlock buttons on the key fob.
Setup New RCDLR	This output control is used to setup up a new remote control door lock receiver
Tire Type/Pressure Selection	Select load range from list Select recommended front tire pressure Select recommend rear tire pressure
TPM Learn Mode	This output controls is the status of the tire pressure monitoring system's learn mode.