DTC P0741. Buick LaCrosse 2006

For 1990-2009 cars only

Makes 🢒 Buick 🢒 2006 🢒 LaCrosse 🢒 DTC 🢒 DTC P0741

DTC P0741 3.6L

Master Electrical Component List
Automatic Transmission Controls Schematics
OBD II Symbol Description Notice

Circuit Description

The transmission control module (TCM) controls the torque converter clutch pulse width modulation (TCC PWM) solenoid valve. The solenoid controls the hydraulic fluid for TCC apply and release. When the TCC is fully applied, the engine is coupled directly to the transmission through the TCC.

The TCC used is an electronically controlled capacity clutch (ECCC). The TCM will normally allow a small amount of slip to occur with the ECCC. When the TCC is engaged, TCC slip speed is maintained at approximately 20 to 50 RPM.

If the TCM detects high torque converter slip when the TCC is commanded ON, then DTC P0741 sets. DTC P0741 is a type B DTC.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0741 Torque Converter Clutch (TCC) System - Stuck Off

Conditions for Running the DTC

•	No TP sensor DTC P0121, P0122 or P0123.

•	No ISS DTC P0716 or P0717.

•	No OSS DTC P0722 or P0723.

•	No TCC stuck ON DTC P0742.

•	No TCC release switch DTC P0842 or P0843.

•	The engine speed is greater than 500 RPM for 5 seconds.

•	The transmission fluid temperature is 20-130°C (68-266°F).

•	The calc. throttle position is between 8 and 90 percent.

•	The TCC PWM solenoid valve is commanded ON.

•	The TCC duty cycle is 65 percent or greater for 5 seconds.

•	The engine torque is 50 N·m (37 lb ft) or more.

•	The commanded gear is 2nd, 3rd or 4th.

Conditions for Setting the DTC

The TCC slip speed is 175 RPM or more 6 times for 5 seconds each during the same ignition cycle.

Action Taken When the DTC Sets

•	The TCM requests the ECM to illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.

•	The TCM forces the TCC OFF.

•	The TCM inhibits TCC engagement.

•	The TCM inhibits 4th gear if the transmission is in Hot Mode.

•	The TCM freezes transmission adaptive functions.

•	The TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as Freeze Frame and Failure Records.

•	The TCM stores DTC P0741 in TCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

Conditions for Clearing the MIL/DTC

•	The ECM turns OFF the MIL after the third consecutive trip in which the TCM does not send an MIL illumination request.

•	A scan tool can clear the MIL/DTC.

•	The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.

•	The TCM cancels the DTC default actions when the ignition switch is OFF long enough in order to power down the TCM.

Diagnostic Aids

•	Prior to replacing the torque converter refer to the Torque Converter Replacement Guide .

•	Residue or contamination may cause valves to stick intermittently.

Test Description

The number below refers to the step number on the diagnostic table.

This step verifies that the TCC engages when commanded ON by the scan tool.

Step

Action

Value(s)

Yes

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

Did you perform the Transmission Fluid Checking Procedure?

Go to Step 3

Go to Transmission Fluid Check

Install a scan tool.
Turn ON the ignition with the engine OFF.

Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. Using the Clear Info function will erase the stored Freeze Frame and Failure Records from the TCM.

Record the Freeze Frame and Failure Records.
Clear the DTCs.
Drive the vehicle at 72 km/h (45 mph).
Using the scan tool, command the TCC PWM solenoid valve ON.
Monitor the TCC Slip Speed.

Does the scan tool indicate the TCC Slip Speed is within the specified value?

-20 RPM to +50 RPM

Go to Diagnostic Aids

Go to Step 4

Inspect the following components:

•	The cooling system for plugging. The cooling lines may be pinched. Refer to Transmission Fluid Cooler Flushing and Flow Test .

•	The TCC control valve for sticking

•	The TCC regulator valve for sticking

•	The pressure regulator valve

•	The TCC PWM solenoid valve stuck and O-ring seal for leaks

•	Refer to Control Valve Body Disassemble in Transmission Unit Repair Manual.

•	The TCC blowoff valve or spring for damage or not seating

•	Refer to Case Cover Components Inspection in Transmission Unit Repair Manual.

•	The TCC signal orifice in the spacer plate plugged

•	The #1 check ball missing or leaking

•	The spacer plate gaskets torn or leaking

•	Refer to Control Valve Body and Spacer Plate Assemble in Transmission Unit Repair Manual.

•	The turbine shaft seals for leaks

•	Refer to Torque Converter Assembly Removal in Transmission Unit Repair Manual.

•	The torque converter clutch

•	Refer to Torque Converter Diagnosis .

Repair or replace the component as necessary.

Did you complete the repair?

Go to Step 5

Perform the following procedure in order to verify the repair:

Select DTC.
Select Clear Info.
Operate the vehicle under the following conditions:

•	Drive the vehicle in D2, D3 or D4 until the TCC is engaged.

•	Calc. throttle position must be 8-90 percent.

•	The TCC is commanded ON at greater than 60 percent duty cycle.

•	TCC slip speed must be between -20 and 55 RPM for at least 4 seconds.

Select Specific DTC.
Enter DTC P0741.

Has the test run and passed?

Go to Step 6

Go to Step 2

With a scan tool, observe the stored information, capture info and DTC info.

Does the scan tool display any DTCs that you have not diagnosed?

Go to Diagnostic Trouble Code (DTC) List - Vehicle

System OK

DTC P0741 3.8L

Master Electrical Component List
Automatic Transmission Controls Schematics
OBD II Symbol Description Notice

Circuit Description

The powertrain control module (PCM) controls the torque converter clutch pulse width modulation (TCC PWM) solenoid valve. The solenoid controls the hydraulic fluid for TCC apply and release. When the TCC is fully applied, the engine is coupled directly to the transmission through the TCC.

The TCC used is an electronically controlled capacity clutch (ECCC). The PCM will normally allow a small amount of slip to occur with the ECCC. When the TCC is engaged, TCC slip speed is maintained at approximately 20 to 50 RPM.

If the PCM detects high torque converter slip when the TCC is commanded ON, then DTC P0741 sets. DTC P0741 is a type B DTC.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0741 Torque Converter Clutch (TCC) System - Stuck Off

Conditions for Running the DTC

•	No VSS DTC P0502 or P0503.

•	No ISS DTC P0716 or P0717.

•	No TCC stuck ON DTC P0742.

•	No TCC release switch DTC P1887.

•	No TCC PWM solenoid valve DTC P2761.

•	The engine is running for greater than 5 seconds and not in fuel cut off.

•	The engine torque is greater than 28 N·m (21 lb ft).

•	The transmission fluid temperature is 20-130°C (68-266°F).

•	The TP indicated angle is 4-99 percent.

•	The IMS indicates D2, D3 or D4.

•	The TCC duty cycle is 50 percent or greater.

Conditions for Setting the DTC

The TCC slip speed is 180 RPM or more for 6 seconds twice during the same ignition cycle:

Action Taken When the DTC Sets

•	The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.

•	The PCM forces the TCC OFF.

•	The PCM inhibits TCC engagement.

•	The PCM inhibits 4th gear if the transmission is in Hot Mode.

•	The PCM freezes transmission adaptive functions.

•	The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.

•	The PCM stores DTC P0741 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

Conditions for Clearing the MIL/DTC

•	The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.

•	A scan tool can clear the MIL/DTC.

•	The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.

•	The PCM cancels the DTC default actions when the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids

•	Prior to replacing the torque converter refer to the Torque Converter Replacement Guide .

•	Residue or contamination may cause valves to stick intermittently.

Test Description

The number below refers to the step number on the diagnostic table.

This step verifies that the TCC engages when commanded ON by the scan tool.

Step

Action

Value(s)

Yes

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

Did you perform the Transmission Fluid Checking Procedure?

Go to Step 3

Go to Transmission Fluid Check

Install a scan tool.
Turn ON the ignition with the engine OFF.

Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. Using the Clear DTC Information function will erase the stored Freeze Frame and Failure Records from the PCM.

Record the Freeze Frame and Failure Records.
Clear the DTCs.
Drive the vehicle at 72 km/h (45 mph).
Using the scan tool, command the TCC PWM solenoid valve ON.
Monitor the TCC Slip Speed.

Does the scan tool indicate the TCC Slip Speed is within the specified value?

-50 RPM to +180 RPM

Go to Diagnostic Aids

Go to Step 4

Inspect the following components:

•	The cooling system for plugging. The cooling lines may be pinched. Refer to Transmission Fluid Cooler Flushing and Flow Test .

•	The TCC control valve for sticking

•	The TCC regulator valve for sticking

•	The pressure regulator valve

•	The TCC PWM solenoid valve stuck and O-ring seal for leaks

•	Refer to Control Valve Body Disassemble in Transmission Unit Repair Manual.

•	The TCC blowoff valve or spring for damage or not seating

•	Refer to Case Cover Components Inspection in Transmission Unit Repair Manual.

•	The TCC signal orifice in the spacer plate plugged

•	The #1 check ball missing or leaking

•	The spacer plate gaskets torn or leaking

•	Refer to Control Valve Body and Spacer Plate Assemble in Transmission Unit Repair Manual.

•	The turbine shaft seals for leaks

•	Refer to Torque Converter Assembly Removal in Transmission Unit Repair Manual.

•	The torque converter clutch

•	Refer to Torque Converter Diagnosis .

Repair or replace the component as necessary.

Did you complete the repair?

Go to Step 5

Perform the following procedure in order to verify the repair:

Select DTC.
Select Clear DTC Information.
Operate the vehicle under the following conditions:

•	Drive the vehicle in D3 or D4 until the TCC is engaged.

•	The transmission fluid temperature is 20-130°C (68-266°F).

•	The TP indicated angle must be 4-99 percent.

•	The engine torque is greater than 28 N·m (21 lb ft).

•	The TCC is commanded ON at greater than 50 percent duty cycle.

•	TCC slip speed must be less than 50 RPM for at least 4 seconds.

Select Specific DTC.
Enter DTC P0741.

Has the test run and passed?

Go to Step 6

Go to Step 2

With a scan tool, observe the stored information, capture info and DTC info.

Does the scan tool display any DTCs that you have not diagnosed?

Go to Diagnostic Trouble Code (DTC) List - Vehicle

System OK