GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

Note: 

   • Always use replacement cables that are of the same type, diameter and length of the cables that you are replacing.
   • Always route the replacement cable the same way as the original cable.


    Object Number: 1861038  Size: SH
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  2. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement.
  3. Open the accessory wiring junction block cover (1).
  4. Remove the accessory wiring junction block nut (2).
  5. Remove the positive battery cable terminal (3) from the stud.
  6. Remove the positive battery cable clip (5) from the multiuse relay bracket.
  7. Push the positive battery cable grommet (6) in through the dash panel.

  8. Object Number: 1861040  Size: SH
  9. Remove the right side instrument panel insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Right Side.
  10. Remove the passenger side carpet. Refer to Front Floor Panel Carpet Replacement - Right Side.
  11. Pull up the passenger side corner of the dash panel sound barrier until the positive battery cable is accessible.
  12. Remove the positive battery cable clip (2) from the stud on the dash panel.
  13. Pull the grommet (1) from the dash panel.
  14. Remove the positive battery cable (3) from the retainers (4) on the body wiring harness.

  15. Object Number: 1861041  Size: SH
  16. Remove the positive battery cable (1) from the body wiring harness right front sill plate (2).

  17. Object Number: 1861042  Size: SH
  18. Remove the body wiring harness (1) from the positive battery cable clips (4).
  19. If equipped with regular production option (RPO) UE1, disconnect the body wiring harness electrical connector (2) from the battery cable electrical connector (3).

  20. Object Number: 1860988  Size: SH
  21. Disconnect the body wiring harness electrical connector (4) from the negative battery cable electrical connector (1).
  22. Disconnect the body wiring harness electrical connector (3) from the battery current sensor (2).

  23. Object Number: 1861043  Size: SH
  24. Remove the positive battery cable clips (1) from the floor panel studs.
  25. Open the positive battery cable cover (2).
  26. Loosen the positive battery cable terminal nut.

  27. Object Number: 1861044  Size: SH
  28. Remove the positive battery cable out from under the rear carpet and remove the cable from the vehicle.

Installation Procedure


    Object Number: 1861044  Size: SH
  1. Route the positive battery cable under the rear carpet and position the cable from the vehicle floor pan.

  2. Object Number: 1861043  Size: SH
  3. Install the positive battery cable clips (1) to the floor panel studs.
  4. Install the positive battery cable terminal to the battery positive terminal.
  5. Caution: Refer to Fastener Caution in the Preface section.

  6. Tighten the positive battery cable terminal nut.
  7. Tighten
    Tighten the nut to 9 N·m (80 lb in).

  8. Close the positive battery cable cover (2).

  9. Object Number: 1860988  Size: SH
  10. Connect the body wiring harness electrical connector (4) to the negative battery cable electrical connector (1).
  11. Connect the body wiring harness electrical connector (3) to the battery current sensor (2).

  12. Object Number: 1861042  Size: SH
  13. Install the body wiring harness (1) to the positive battery cable clips (4).
  14. If equipped with RPO UE1, connect the body wiring harness electrical connector (2) to the battery cable electrical connector (3).

  15. Object Number: 1861041  Size: SH
  16. Install the positive battery cable (1) to the body wiring harness right front sill plate (2).

  17. Object Number: 1861040  Size: SH
  18. Push the grommet (1) through the dash panel.
  19. Install the positive battery cable (3) to the retainers (4) on the body wiring harness.
  20. Install the positive battery cable clip (2) to the stud on the dash panel.
  21. Reposition the passenger side corner of the dash panel sound barrier.
  22. Install the passenger side carpet. Refer to Front Floor Panel Carpet Replacement - Right Side.
  23. Install the right side instrument panel insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Right Side.

  24. Object Number: 1861038  Size: SH
  25. Ensure that the positive battery cable grommet (6) is completely seated through the dash panel.
  26. Install the positive battery cable terminal (3) to the junction block stud.
  27. Install the accessory wiring junction block nut (2).
  28. Tighten
    Tighten the nut to 22 N·m (16 lb ft).

  29. Close the accessory wiring junction block cover (1).
  30. Install the positive battery cable clip (5) to the multiuse relay bracket.
  31. Install the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement.
  32. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.