GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 2000 🢒 Century (China) 🢒 Body and Accessories 🢒 Wiring Systems 🢒 Crankshaft Position Sensor Replacement

Crankshaft Position Sensor Replacement 7X CKP Sensor

Removal Procedure

    Object Number: 15969 Size: SH
  1. Turn OFF the ignition switch.
  2. Crank steering wheel fully to the left.
  3. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  4. Disconnect the sensor electrical connector.
  5. Remove the attaching bolt/screw.
  6. Remove the sensor from engine.
  7. Inspect for wear, cracks, or leakage if the sensor is not being replaced.

Installation Procedure
  1. Lubricate the O-ring with clean engine oil before installation and replace if damaged.

    2. Object Number: 15969 Size: SH
  2. Install the sensor to the block.

    3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Reinstall the sensor attaching bolt.

    4. Tighten
    Tighten the bolt to 8 N·m (71 lb in).

  4. Connect the sensor electrical connector.
  5. Lower the vehicle.

Crankshaft Position Sensor Replacement 24X CKP Sensor

Removal Procedure

    Object Number: 14714 Size: SH
  1. Turn OFF the ignition.
  2. Remove the serpentine drive belt from crankshaft pulley. Refer to Drive Belt Replacement in Engine Mechanical.
  3. Raise the vehicle on hoist. Refer to Lifting and Jacking the Vehicle in General Information.
  4. Remove the crankshaft harmonic balancer retaining bolt.
  5. Remove the crankshaft harmonic balancer. Refer to Drive Belt Tensioner Replacement in Engine Mechanical.
  6. Note the routing of sensor harness before removal.
  7. Remove the harness retaining clip with bolt (1).
  8. Disconnect the sensor electrical connector.
  9. Remove the sensor bolts (2).
  10. Remove the sensor.

Installation Procedure

    Object Number: 14714 Size: SH
  1. Install the 24X crankshaft position sensor with bolts (2) and route harness as noted during removal.

    2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the harness retaining clip with bolt (1).

    3. Tighten
    Tighten the bolts to 10 N·m (8 lb ft).

  3. Connect the sensor electrical connector.
  4. Reinstall the balancer on the crankshaft. Refer to Drive Belt Tensioner Replacement in Engine Mechanical.
  5. Apply thread sealer GM #1052080 or equivalent to threads of the crankshaft harmonic balancer bolt.

    6. Tighten
    Tighten the bolt to 150 N·m  (110 lb ft).

  6. Lower vehicle.
  7. Reinstall the serpentine drive belt. Refer to Drive Belt Replacement in Engine Mechanical.
  8. Perform the Crankshaft Position System Variation Learn .