GM Service Manual Online
For 1990-2009 cars only

Circuit Description

When the ignition is turned ON, the inflatable restraint sensing and diagnostic module (SDM) performs tests to diagnose critical malfunctions within itself. When the SDM has completed the power-up mode the SDM will establish communication with the Passenger Presence System (PPS). The PPS will respond by commanding both the PASSENGER AIR BAG ON/OFF indicators located in the center of the instrument panel cluster (IPC) ON for 5 seconds. The SDM will transmit a request message to the PPS to receive the PPS verification ID. The PPS will transmit the verification ID to the SDM and the SDM will compare the ID received to data stored in memory. The SDM will also set DTC B0092 to notify the driver that the PPS has a current malfunction present. When the SDM detects that the PPS has set any one of the following DTCs, 032, 034, 036, 052, or 056 the SDM will then disable the instrument panel (I/P) module deployment loop, set DTC B0092 and command the AIR BAG indicator ON.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC B0092 Passenger Presence System Performance

Conditions for Running the DTC

Ignition 1 voltage is within the normal operating voltage range.

Conditions for Setting the DTC

    • The SDM has loss or never established communications with the PPS.
    • The SDM detects that the PPS has set a DTC.

Action Taken When the DTC Sets

    • The SDM disables the I/P deployment loop.
    • The SDM commands the AIR BAG indicator ON via class 2 serial data.
    • The PPS will turn ON the PASSENGER AIR BAG OFF indicator.

Conditions for Clearing the DTC

    • The condition responsible for setting the DTC no longer exists.
    • You issue a scan tool CLEAR DTCs command.
    • A history DTC will clear once 255 malfunction-free ignition cycles have occurred.

Diagnostic Aids

DTC B0092 is an indication that the SDM has no or loss communication with the PPS or the PPS has internal faults/DTCs. The SDM will communicate to request the verification ID from the PPS for 5 seconds. If the SDM does not receive the verification ID from the PPS within 5 seconds the SDM will set the DTC as current, illuminate the AIR BAG indicator, and disable the I/P deployment loop.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step checks the PPS for any current or history DTCs.

  2. Test the occupant sensor serial data circuit for an open or high resistance.

  3. Test the PPS ignition 1 voltage circuit for a short to ground, a high resistance, or an open.

  4. Test the PPS ground circuit for an open or high resistance.

  5. Test the PPS ground circuit for a short to voltage.

Step

Action

Yes

No

Schematic Reference: SIR Schematics

Connector End View Reference: SIR Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Important: If the PPS has any current or history DTCs stored, you must address the PPS DTCs before continuing with this diagnostic table.

  4. Use the scan tool to request the Passenger Presence System (PPS) DTCs. Refer to Passenger Presence System Flash Code Procedures .

Does the PPS flash any current or history DTCs?

Go to Diagnostic Trouble Code (DTC) List - Vehicle

Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the PPS module connector. Refer to Control Module References for replacement, setup, and programming.
  3. Inspect the PPS module connector for corrosion or damage. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 10

Go to Step 4

4

  1. Disconnect the inflatable restraint sensing and diagnostic module (SDM) connector. Refer to Control Module References for replacement, setup, and programming.
  2. Inspect the SDM connector for damage or corrosion. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 10

Go to Step 5

5

Test the occupant sensor serial data circuit for an open or high resistance between the PPS and SDM connector. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 10

Go to Step 6

6

Test the PPS ignition 1 voltage circuit for the following:

    • A short to ground
    • A high resistance
    • An open

Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 10

Go to Step 7

7

Test the PPS ground circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 10

Go to Step 8

8

  1. Turn ON the ignition, with the engine OFF.
  2. Test the PPS ground circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 10

Go to Step 9

9

  1. Turn OFF the ignition.
  2. Important: The PPS is a calibrated system. The PPS must be rezero after replacement.

  3. Replace the PPS, the PPS is only serviceable as PPS, heated seat element, and seat bottom foam assembly. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 10

--

10

  1. Reconnect all SIR and PPS system components.
  2. Verify that all components, connectors, and connector position assurances (CPAs) are properly mounted.
  3. Use the scan tool in order to clear the SIR and PPS DTCs.
  4. Rezero the PPS. Refer to Control Module References for replacement, setup, and programming.
  5. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK